Hi Murray,

Did u had time to test 1 2

Am I the only one in this case 1 2

Thanks

--- In kiwitechnics@yahoogroups.com , Kiwitechnics <yahoogroups@...> wrote:
>
> Thanks for the details. I will test this shortly as soon as I get some time.
>
> Regards
> Murray
>
> On 8/11/2011 6:41 a.m., poiskaill wrote:
> >
> > Hi,
> >
> > After more tests, it almost works fine. But there are still things I
> > don't explain.
> >
> > First, the global parameters are:
> > B1 = 1
> > B2 = 16 (tried with 1 too)
> > B3 = not used
> > B4 = 1
> > B5 = 1
> > B6 = 0
> > B7 =1
> > B8 = 0
> > B9 = 0
> > B10 = 0
> > B11 = 0
> >
> > I've tried with 2 midi interfaces, with just one. The result is the same:
> > Now, I can play and record the jx-3p but, there are still midi
> > artefacts occuring anytime. It's ok for a few measures and then the
> > seq is pertubed by some midi notes.
> > There's always a high and a low note, and they never get off unless I
> > use the panic button.
> >
> > This is what I monitored when the artefact happens:
> > TIMESTAMP IN PORT STATUS DATA1 DATA2 CHAN NOTE EVENT
> > 00286C77 14 10 9F 00 00 16 C -1 Note Off
> > 00286C77 14 15 9F 00 00 16 C -1 Note Off
> > 00286C79 14 10 9F 20 71 16 G# 1 Note On
> > 00286C79 14 15 9F 20 71 16 G# 1 Note On
> > 00286CF7 14 10 9F 20 00 16 G# 1 Note Off
> > 00286CF7 14 15 9F 20 00 16 G# 1 Note Off
> > 00286CF9 14 10 9F 00 71 16 C -1 Note On
> > 00286CF9 14 15 9F 00 71 16 C -1 Note On
> >
> > Note: the midi sequence doesn't play these notes.
> >
> > It happens also when only the midi in is plugged in the 3p ! Very
> > surprising !!
> >
> > I really don't understand how it could sound like a midi loop with
> > only the midi in connected.
> >
> > Murray did you sequence the 3p in your tests 1 2
> > Nobody with the same problem 1 2
> >
> > Thanks
> >
> > --- In kiwitechnics@yahoogroups.com
> > <mailto:kiwitechnics%40yahoogroups.com>, "poiskaill" <poiskaill@>
> > wrote:
> > >
> > > Hello and thanks for your reply !
> > >
> > > I've managed to access to the global parameters:
> > > I put 'goup a / bank b / 8 & 9' on the first position. I think it's
> > the off position cause my sytem works better now.
> > > I set midi channel in on 1 and the out on 16.
> > >
> > > There are still things non ok:
> > > - the output sends a lot of CC: LSB & MSB, also the PC Brite acc
> > piano (on all the sounds, it send this specific PC).
> > >
> > > - Recording midi notes: I can record every type of instruments with
> > one note at the time (piano, bass, pad). I can also record chords with
> > a piano sound, but I can't with a pad: when I release the keys, the
> > notes are still active and then release after. Also, if I play a new
> > chord or notes during this note sustaining, the midi recorder can't
> > see the new notes.
> > >
> > > I'll try to make a video of it, will be easier to understand ;)
> > >
> > > Also,
> > > on the website, the last 3p upgrade's update is not downloadable
> > (error 404).
> > >
> > > best regards
> > > F
> > >
> > >
> > >
> > > --- In kiwitechnics@yahoogroups.com
> > <mailto:kiwitechnics%40yahoogroups.com>, Kiwitechnics <yahoogroups@>
> > wrote:
> > > >
> > > > Assuming you are using v2, try turning off Global Parameters Group
> > > > A:Bank B:8 & 9. This will switch off the passing of midi from the
> > in to
> > > > the out ports.
> > > > Midi Channels are also set in Group A:Bank B:1
> > > >
> > > > Sorry the manual is hard to read. It's a little complicated. Print
> > out a
> > > > A3 colour copy of the Menu Map as that will help you to find your way
> > > > around.
> > > >
> > > > To edit the global parameters you press Shift (tape button), Group A:
> > > > Bank B: then 1 to 16 depending on the parameter you wish to edit.
> > There
> > > > is a table of these in the menu map.
> > > >
> > > > MH
> > > >
> > > > On 6/11/2011 9:57 a.m., poiskaill wrote:
> > > > >
> > > > > Hi,
> > > > >
> > > > > Since I've installed the 3p ugrade, I don't recognize the use of my
> > > > > synth, and I feel really lost reading the 3p upgrade's manual.
> > > > >
> > > > > The 3p has midi in & out connected (it's also my master keyboard).
> > > > > I can get it work properly: there's a midi loop I can't get rid
> > of (no
> > > > > loop before the upgrade).
> > > > > Also, just with the midi in connected, a single note sent from
> > Cubase
> > > > > and the 3p takes the notes and keep it alive, no way to stop it.
> > > > >
> > > > > I have also the PE wich is working fine thru Cubase. No problem
> > > > > controlling the 3p on the same channel the notes were send.
> > > > >
> > > > > How to go in 'global parameters' to set the midi channels 1 2
> > > > >
> > > > > I think It should be a good start ;)
> > > > >
> > > > >
> > > >
> > >
> >
> >
>