hello,
in my case, when the a155 sequences seem to me a bit
"off-sync", i use the a160 divider plus the a162 dual
trigger delay. with the right a190 clock dividing
value and the right a162 delay settings, plus the
right a160 clock divider output, i always get, in the
end, a clock pulse that is in total sync with my
midi-clock.
hope this helps.
bakis.



--- Dieter Doepfer < hardware@... > wrote:

> Sixtoo,
>
> the clock divider module A-160 will not really help
> as it divides only by 2,
> 4, 8 ...
>
> I know that the A-190 programming is a bit awkward
> but it should be possible
> to obtain the right dividing factor. Pay attention
> that in the A-190 manual
> the program change numbers are counted from 1...128.
> Other manufacturers
> count from 0...127. For some devices (especially
> software) you may be able
> to select between the counting methods 0...127 and
> 1...128 (finally always
> 0...127 is sent by Midi but the display of the
> transmitting device may show
> the range 0...127 or 1...128). Maybe you will have
> to subtract 1 from the
> statements in the A-190 manual to obtain the right
> program change number.
>
> You have to send e.g. Midi program change #3 (#2 if
> 0...127 is counted) or
> #6 (#5 if 0...127 is counted) while you are in the
> CONFIG menu 2 (clock
> time/polarity). Then you have to leave the CONFIG
> mode and look if the
> dividing factor is correct. And you have to store
> the settings (page 17) to
> have the same dividing factor available after power
> off/on.
>
> Best wishes
> Dieter Doepfer
>
> > -----Ursprüngliche Nachricht-----
> > Von: Doepfer_a100@yahoogroups.com
> > [mailto: Doepfer_a100@yahoogroups.com ]Im Auftrag
> von Sixtoo.1200Hobos
> > Gesendet: Dienstag, 7. Februar 2006 06:15
> > An: Doepfer_a100@yahoogroups.com
> > Betreff: Re: 1 Digest Number 1401
> >
> >
> > Hello Dieter and also to the rest of the folks on
> here. Thanks for
> > the feedback. I checked page 10 in the manual, and
> since I am not sending
> midi
> > messages via an external controller, I think I
> might still be having
> > problems somewhere in the programming of the 190
> itself. I have
> > tried every possible division (programming step at
> a time in the FLO
> > Freq/Clock menu) by hand, and everything still
> seems to send a non-
> > quartered (triplets ) hardware pulse to the
> filters that I am trying
> > to control. Would it be easier for me to just add
> a clock divider
> > module between the 190 and 155... and then send
> different divisions
> > to different dedicated filters and to the
> sequncer
> >
> > Sixtoo
> >
> >
> >
> >
> > "You have to set the clock dividing factor to 6,
> 12 or 24 to get
> > 1/16, 1/8 or
> > 1/4 hardware clock pulses from the A-190. Please
> look at the A-190
> > manual to
> > page 10. I know that the A-190 operation is not
> the best (I would never
> > design the A-190 again as it is but it was
> develeoped by an employee in
> > cooperation with an external consultant - in the
> meantime I don't
> > think much
> > of external consultants but listen to the
> suggestions of this
> > group ....)"
> >
> > Best wishes
> > Dieter Doepfer
> >
> >
> >
> > [Non-text portions of this message have been
> removed]
> >
> >
> >
> >
> > Yahoo! Groups Links
> >
> >
> >
> >
> >
> >
>
>
>
>
> Yahoo! Groups Links
>
>
> Doepfer_a100-unsubscribe@yahoogroups.com
>
>
>
>
>
>

Bakis Sirros - Parallel Worlds
1 group owner
http://www.parallel-worlds-music.com
http://www.shimarecords.co.uk
http://www.rubber.gr
Athens-Greece

__________________________________________________
Do You Yahoo!
Tired of spam Yahoo! Mail has the best spam protection around
http://mail.yahoo.com