Thanks Bakis !

terry.

--- In Doepfer_a100@yahoogroups.com , Bakis Sirros <synth_freak_2000@y...> wrote:
>
> hello ingo, moogy,
> no. the problem is that moogy does not have a vca
> patched after his vco.
> so, moogy, here's what connections you need for a
> basic synth patch:
> voyager cv out-> a185 cv in(from there the cv signal
> is internaly distributed, via the system bus, to the
> doepfer a110 vco's, no more connections to the a110's
> needed)
>
> voyager gate out-> a185 gate in(from there the gate
> signal is internally distributed, via the system bus,
> to the a140 envelopes, no more connections to the
> a140's needed)
>
> a110 audio out-> vcf audio in
> vcf audio out->vca audio in.
> vca audio out-> your mixing console.
> a140 cv output-> vca cv input(for controlling the
> volume of your synth sound)
> a140 cv output->vcf cv input(for controlling the
> timbre/brilliance of the sound)
> so, now everything should work fine.
> and do get a book about modular synthesis. it is the
> only way to really apreciate the value of your modular
> system.
> best regards,
> bakis.
>
>
>
>
>
> --- selfoscillate <synaptic_music@y...> wrote:
>
> >
> > hello,
> >
> > i think the problem is the gate setting on the
> > voyager.
> > i don't have a voyager in the studio regularly, but
> > from time to time i use one and i remember that i
> > had similar
> > problems with the gate and i just had to change a
> > single
> > setting on the yoyager and it worked, but i cannot
> > recall
> > which setting it was.
> >
> > best wishes
> >
> > ingo
> >
> >
> >
> > --- In Doepfer_a100@yahoogroups.com , "moogy"
> > <moogy9918@y...> wrote:
> > >
> > >
> > > Hi Everyone,
> > >
> > > Firstly here is a list of modules in my new
> > system,
> > >
> > > G6 case
> > > A-185 bus access
> > > A-102 diode filter
> > > A-118 noise source
> > > 3xA-140 ADSR
> > > 2xA-146 LFO
> > > A-160 clock divider
> > > A-161 clock sequencer
> > > 2x A-180 multiples
> > > A-138 mixer
> > > A-108 VCF
> > > A-179 LCV
> > > A-119 external in
> > > A-114 ring mod
> > > 2x A-110 VCO
> > > A-131 VCA
> > > A-137 VC wave multiplier
> > > A-199 spring reverb
> > >
> > > I'm using an MCV-4 being triggered by a Voyager.
> > >
> > > Here's my problem,
> > >
> > > I have the gate connection from the MCV4 going to
> > 'gate in' on the
> > > bus access and CV1/2 fom the MCV into 'CV in' on
> > the bus access.
> > > 'Gate Out' from bus access goes to 'Gate In' on
> > the ADSR.Output
> > from
> > > the ADSR goes to 'CV1' on a VCO.Sawtooth output
> > from the VCO goes
> > to
> > > output on the mixer.
> > > Under these conditions I'm getting a continously
> > sustained note.The
> > > Voyager is articulating notes from the VCO and the
> > ADSR is
> > triggered
> > > and produces an envelope but once the envelope
> > cycle finishes the
> > > system produces a sustaining note.If I remove the
> > ADSR to VCO CV1
> > > connection the system will still articulates notes
> > from the Voyager
> > > but still returns to a sustaining note.
> > >
> > > I've tried various set ups but still can't get rid
> > of the sutaining
> > > note...hope my description is clear enough,can
> > anyone please help,
> > >
> > > thanks,
> > >
> > > terry.
> > >
> >
> >
> >
> >
> >
>
>
> Bakis Sirros - Parallel Worlds
> 1 group owner
> http://www.parallel-worlds-music.com
> http://www.shimarecords.co.uk
> http://www.rubber.gr
> Athens-Greece
>
>
>
> __________________________________________
> Yahoo! DSL – Something to write home about.
> Just $16.99/mo. or less.
> dsl.yahoo.com
>