I wonder if you can get a panel blank for this gap. My Doepfer portable case has two very small blanks on the left side (they appear to be about 1hp each). I'd contact Analogue Haven.

Bryan

>>> david.salter@... 09/14/05 3:06 AM >>>

Hi Seth,

Attached is link to the picture (bit fuzzy, sorry) showing the VCS
mounted into a Doepfer G6.

http://img1.yoxio.com/img/197630.jpg

As you can see there is a gap of just under 1HP. Because I'd removed two
modules to install the VCS my natural assumption was that the VCS's
mounting holes were out. On closer inspection you should be able to make
out that the lower mounting rails on my G6 are slightly off.

Sincere apologies for the scare but I can confirm (because I did try
moving the module to the upper level) that the VCS mounts fine.

BTW a great module. Followed some suggestions from Ingo and the Serge
Gold Guide and have now got the VCS working as a VC LFO, VCF, VC
Envelope and VCO. More to experiment with.

Many thanks

David

David Salter
Senior Project Manager
Reuters Ltd
Tel +44 20 7542 2402
Mob +44 7990562402
email david.salter@...
RM david.salter.reuters@...


-----Original Message-----
From: info@... [mailto: info@... ]
Sent: 12 September 2005 18:38
To: David Salter
Subject: RE: bananalogue VCS

hi david,

just wanted to write a quick note to ask you if you could please send me
a digital photo of what your modules looks like mounted im concerned
about the space you mention. we tested mounting the modules in a
doepfer super-case, but if there is a mounting hole desprepency i need
to take measures to fix that. thanks! ill write again later with some
more comments and suggestions for using the VCS module!

best wishes!
seth nemec

> Hi Seth,
>
> My module has arrived, many thanks.
>
> I want to give you some feedback first as I'll be posting something
> onto the Doepfer forum as well.
>
> Speed of service and communications have been excellent. I made my
> first enquiry at the end of July and received my module 6 weeks later.

> So no complaints there.
>
> First impressions. Excellent packing containing a very nice looking
> module, ribbon cable (too short for my custom rack but long enough for

> a G6), mounting screws (always nice to see) and a two page information

> pack.
>
> I had to remove a couple of modules to try it out so it went into the
> bottom left corner of a Doepfer G6 rack. The info pack has a clear
> diagram to ensure that the ribbon goes correctly. Comment number 1;
> the mounting holes do not conform to either the Doepfer or Analogue
> Systems spec which means I have a gap either side of the module. Not a

> big deal but does affect the appearance.
>
> The info pack has a labelled panel drawing (as per website) and the
> connection details. Comment 2; I would really have appreciated a
> manual of some kind. Although I've had my Doepfer Analogue Sys. System

> for a while I have no experience with Serge kit and some starting
> suggestions would have been useful.
>
> Started off by injecting a ramp wave in and listening. Played with the

> various controls and started getting some nice sync type tones. Added
> a single LFO to modulate each of the CV's and then both CV's (love the

> pull for expo curve on these pots) again some really interesting tone.
>
> A hour later and I have not tried using it beyond this type of
> function, would appreciate some guidance, but a very happy man so far.
>
> With luck Bananalogue will produce more Serge based modules I do hope

> so.
>
> Best wishes
>
> David
>
>
>
> David Salter
> Senior Project Manager
> Reuters Ltd
> Tel +44 20 7542 2402
> Mob +44 7990562402
> email david.salter@...
> RM david.salter.reuters@...
>
>
> -----Original Message-----
> From: info@... [mailto: info@... ]
> Sent: 01 September 2005 22:26
> To: list@...
> Subject: [spam] bananalogue list and news!
>
> hello!
>
> you are recieving this message because you have either ordered a
> bananalogue VCS module, or expressed interest in the past. i created
> the list as an efficient means to send genreal news updates. if you
> would like to be removed from the list, or would like to subscribe at
> a different email address, please email me: info@...
>
> now the first news update!
>
> VCS modules are shipping as we test and pack them. some of you should

> find your module in the mail this week or next.
>
> we will also be taking orders for the second run of doepfer-sized
> modules in the very near future. if you are on the waiting list, you
> will be contacted about payment before we open up the ordering process

> to the general public.
>
> also, the VCS will be made availible in a limited number of frac-rack
> modules sometime in september. i will send out another message to the

> list when they are ready.
>
> thats it for now - as always, please email me if you have any
> questions or concerns. thanks!
>
> seth nemec
> info@...
>
> www.bananalogue.com
>
>
>
>
>
> -----------------------------------------------------------------
> Visit our Internet site at http://www.reuters.com
>
> To find out more about Reuters Products and Services visit
> http://www.reuters.com/productinfo
>
> Any views expressed in this message are those of the individual
> sender, except where the sender specifically states them to be the
> views of Reuters Ltd.
>
>
>

-----------------------------------------------------------------
Visit our Internet site at http://www.reuters.com

To find out more about Reuters Products and Services visit http://www.reuters.com/productinfo

Any views expressed in this message are those of the individual
sender, except where the sender specifically states them to be
the views of Reuters Ltd.



SPONSORED LINKS
A100 Modular system Synthesizer Electronic payment Electronic test equipment Guitar synthesizer
YAHOO! GROUPS LINKS

Visit your group "Doepfer_a100" on the web.
To unsubscribe from this group, send an email to:
Doepfer_a100-unsubscribe@yahoogroups.com
Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.