>
> hello coleman,
> gate bus leds for midi the three leds of the bus
> board are only for +12 -12 and +5 volts supply, not
> for midi.

Sorry, then the LED's on the gate out of the bus access on a A185..
Showing that the bus is receiving the signals.

> you mean the cv/gate leds of the a190 module

Yes.. the LED will light and there will be the correct gate sent when a
key on the midi keyboard is sent-

> doesn't proove that the cv/gate signal is transmitted
> into the bus board, though.
> are you sure that you haven't cut the two solder links
> that connect the a190 cv/gate signals to the rack's
> busboard

I have not cut them. I have not been able to get any of the CV data
from the module.

>also, are the two cv/gate singals jumpers
> that connect the two halfs of the busboards in place
> if you have the a190 in one side of the rack and the
> vco's in the other and the jumpers are missing, then
> you still do not get any cv/gate signals to these
> vco's, as the bussboard is cut in two halfs(regarding
> cv/gate distribution).
> bakis.

I understand, but if I patch the A190 directly into a VCO, i'd see/hear
something.

>

> >
> > > What kind of device is fed by the CV-Out

by patch into the A110 VCO

> > > Did you measure the note CV already with nothing
> > connected to
> > >
> >
> >
> Message: 3
> Date: Thu, 11 Nov 2004 10:10:05 -0800 (PST)
> From: Bakis Sirros < synth_freak_2000@... >
> Subject: Fwd: AW: A190 issues..(dieter's reply)
>
>
> --- Dieter Doepfer < hardware@... > wrote:
>
> > From: "Dieter Doepfer" < hardware@... >
> > To: "Bakis Sirros" < synth_freak_2000@... >
> > Subject: AW: 1 A190 issues..
> > Date: Thu, 11 Nov 2004 17:39:54 +0100
> >
> > > It's connected to the bus, so I can see the gate
> > bus LED's lit when
> > > there is midi data received, I have also tried
> > patching it to any of my
> > > A110 VCO's, still no use. It's odd, i know that
> > the IC is working,
> > > which would be the suspect thing if it were blown,
> > as the gate outs are
> > > okay.. so any ideas
> >
> > Explanation #1: There are 2 modules that "write" to
> > the CV line of the bus.
> > So far this could be the A-185 only (or two A-190).
> > If you have an A-185 on
> > the same bus the bus connections of the A-190 have
> > to be interrupted as
> > mentioned on page 4 in the A-185 manual.
> >
> > Explanation #2: The A-190 is defective or completely
> > misadjusted. Try to
> > measure the CV at the CV socket at the front panel.
> > If there is no CV coming
> > out reset the A-190 as described in the A-190
> > manual.

I have performed the 2 types of resets.



























Hooking a multimiter to the outputs, the gate outputs a +5V gate, CV1
outputs .037 constantly and CV2 outputs between 0v and +5V depending on
velocity sent through midi. Maybe the Pot inside is cranked all the way
down I have not had this module work at any time.















Hope this clears some issues up-

Coleman.

> > scale and offset of the A-190 have to be re-adjusted
> > (i.e. VCOs controlled
> > by the A-190 will probably be detuned especially
> > because of the unadjusted
> > 1V/octave scale).
> >

__________________________________
Do you Yahoo!
Check out the new Yahoo! Front Page.
www.yahoo.com