Ingo, that's great and very interesting and informative. Thanks much for
posting these.

--Chuck

> -----Original Message-----
> From: selfoscillate [mailto: synaptic_music@... ]
> Sent: Monday, September 06, 2004 1:56 AM
> To: Doepfer_a100@yahoogroups.com
> Subject: 1 sound examples
>
>
>
> hello list,
>
> here are some of the requested sound examples.
> all files are 110 bpm and they should also
> work as loops.
>
> for all the examples the same sequence was used.
> the pulse wave of an a111 vco is the audio source.
> the end of the signal chain is an a131 vca, controlled
> by an a140 adsr. the different patches had different
> output volumes. therefore the output level of the vca
> was re-adjusted on each patch.
>
> this is the a111 pulsewave output:
>
> http://www.selfoscillate.de/a100files/osc+vca.mp3
>
>
> then the modules in question were patched between
> the vco and the vca.
>
>
> a101-3 vactrol phaser, modulated by an a147 lfo (triangle).
> example 1 is a 6-stage patch with simple lfo modulation.
> example 2 is the same as example 1, but in 12-stage mode.
> example 3 is a 6-stage-patch with a more complex lfo
> modulation (vco pitch cv modulates the lfo frequency).
> example 4 is the same as example 3, but in 12-stage mode.
> example 5 is the same as example 4, but the lfo modulation
> is inverted for the vactrols 7 - 12.
>
> http://www.selfoscillate.de/a100files/a101-3-take-1.mp3
> http://www.selfoscillate.de/a100files/a101-3-take-2.mp3
> http://www.selfoscillate.de/a100files/a101-3-take-3.mp3
> http://www.selfoscillate.de/a100files/a101-3-take-4.mp3
> http://www.selfoscillate.de/a100files/a101-3-take-5.mp3
>
>
>
> a102 diode filter, with different settings for level and
> resonance, cutoff modulated by an a145 lfo (triangle).
> on the examples 2, 3 and 4 the filter cutoff was
> additionally controlled by the vco pitch cv (keytracking):
>
> http://www.selfoscillate.de/a100files/a102-take-1.mp3
> http://www.selfoscillate.de/a100files/a102-take-2.mp3
> http://www.selfoscillate.de/a100files/a102-take-3.mp3
> http://www.selfoscillate.de/a100files/a102-take-4.mp3
>
>
>
> a107 morphing filter in different modes:
> example 1 is filter mode 04 (12db low + 6db high), with
> keytracking and lfo modulation (triangle) on the cutoff,
> resonance is close to self-oscillation.
> example 2 is the same as example 1, but in filter mode 21,
> which is a 6db highpass.
> example 3 is the same as example 1, but in filter mode 16
> (lowpass + notch 2) and without lfo modulation.
> example 4 is a morph between 7 filtermodes, going from
> mode 26 to 32 and back, without any other modulation
> (fixed cutoff), but with maximum input level and maximum
> resonance.
>
> http://www.selfoscillate.de/a100files/a107-take-1.mp3
> http://www.selfoscillate.de/a100files/a107-take-2.mp3
> http://www.selfoscillate.de/a100files/a107-take-3.mp3
> http://www.selfoscillate.de/a100files/a107-take-4.mp3
>
>
>
> a108 48db lowpass with a101-3 vactrol phaser patched
> into the a108 feedback loop. keytracking is used on both a108
> and a101-3. the 24db lowpass output of the a108 is fed into
> the a101-3 audio input. the a101-3 output for stage 4 is
> fed back into the a108 resonance input jack. the 48 db
> lowpass output is used as audio output for the final vca.
> during recording the polarizer 1 on the a101-3 was turned
> from "fully counter clockwise" (negative feedback) to
> "fully clockwise" (positive feedback).
>
> http://www.selfoscillate.de/a100files/a108-a101-3-take-1.mp3
>
>
>
> a133 polarizer, used to modulate the vco waveform.
> the vco pulsewave is fed into the audio input of the a133.
> the vco sinewave is fed into the cv input of the polarizer.
> during recording the a133 cv attenuator was turned from
> "fully counter clockwise" to "fully clockwise".
>
> http://www.selfoscillate.de/a100files/a133-take-1.mp3
>
>
>
> a196 pll, patched between vco and vca, with the following settings:
> offs=5, range=mid, type=2, lowpass freq=2
>
> http://www.selfoscillate.de/a100files/a196-take-1.mp3
>
>
>
> ok, thats all for now. i don't think that detailed parameter settings
> are really necessary for these examples. anyway, if somebody is
> interested in more details, please contact me via email.
>
> best wishes
>
> ingo
>
>
>
>
>
>
>
>
> Yahoo! Groups Links
>
>
>
>
>
>