hi Peter,
I'm in for at least one... would like two, but just put a deposit on the new EH 16 sec delay.... so not sure I can afford two now... too many new toys!
best,
phil

> Based on interest expressed from your letters (thank you!) and
> after speaking with Dieter and getting the thumbs up to produce
> my VCO, it looks I'm going to do just that in a limited quantity.
>
> These will be marketed under the company name 'Plan B' and
> will be in Doepfer height, 90mm wide (45HP), will use the same
> jacks as Doepfer but with the soft touch knobs used by Analogue
> Systems. The will run on either +/112 or +/-15 and will use
> Doepfer's 16 pin dual in line power configuration on the PCBs.
> For a general idea of what this VCO will look like, go here:
>
> http://www.buzzclick-music.com/Doepfer_rendered2.jpg
>
> I'm going to d a maximum of 25 pieces, but will need a minimum
> of a 10 piece order to go forward with this.
>
> Price: $200.00.
>
> Payment: 50% down, 50% plus shipping (FOB Los Angeles, CA)
> on completion prior to shipment. Paypal is preferred, money
> orders accepted, please no cash or cpersonal checks.
>
> Schedule:
>
> I am not by any means even close to a large scale manufacturer.
> I am requesting 50% down so that the components may be
> purchased and the faceplates and PCBs can be produced. I
> have about a week's worth of finalization to do on the design to
> get it to production status. Once this happens and orders are
> received, I will purchase the raw materials and we can expect 4
> weeks from that date for delivery of the PCBs and faceplates. I
> will need approx 1 day per unit for assembly, testing and
> calibration after that. I apologize for the way I have to handle this,
> but again - I'm not a large scale manufacturer!
>
> These will come with a 1 year warranty for anomalies caused by
> manufacturing. Damage due to misuse must be billed, but at
> only a $25 surcharge during the first year (not including parts).
>
> I AM NOT TAKING ORDERS YET! I do ask that you contact me
> offline to determine the demand for this module and if it warrants
> going into production. During this time I'll be working on the
> design finalization.
>
> You can get me at peter@...
>
> Due to the complexity of this assemnby I will not be able to sell
> bare PCBs at this time. This VCO incorporates a
> heat-conductive epoxy encaspulated sub module for
> temporature stability and both through hole and SMT
> components - it's a tricky assembly process.
>
> So let me know if you're interested and thanks again for
> expressing interest in this instrument.
>
> Features:
>
> Controls:
>
> Freq
> Fine Freq
> Freq VC1 attenuation
> Freq VC1 attenuation
> FM level
> Wave Morph
> Pulse Width
>
> Jacks:
>
> Outputs:
>
> Sine out
> Triangle out
> Saw out
> PWM out
> Morph out
>
> Inputs:
>
> Freq VC 1
> Freq VC 2
> FM in
> 1v/oct in
> Sync
> Wave Morph VC
>
> Switches:
>
> Wave Morph Wave B select
>
> General Specs:
>
> Frequency range: 5 to 20K hertz
> Fine Freq range: 20 hz
> 2 bipolar control voltage inputs (full + and - processing)
> Expo FM
> Manual and VC crossfade WaveMmorphing from Sine to either
> Saw or Square
> Manual and VC PWM
> One 1 volt/octave input
>
> best,
>
> Peter Grenader
> (now of Plan B!)
>
>
>
>
>
> Yahoo! Groups Links
>
>
>
>
>