Hi David

When using the A191 as a clock source, I generally split the clock
signal to both the A155 and the A160 clock divider. The A160's 1/8
socket (or whatever) would be patched to an A150 VC Switch, which
alternately selects the trigger (upper half of A150) and pitch CV
(lower half of A150) from the upper or lower row of the A155. This
gives you a 16-step sequence, as described in the A155 User's Guide.

Since I was spoiled by the A191, I didn't bother to use the A190's
clock output until recently. Both the A190 clock output or the A191
LFO sockets can be divided, so one can be used to clock the sequencer
and the other used at 1/8 the other's rate, to close the A150 VC
Switch. An A160 clock divider isn't needed with this arrangement.

Joe

--- In Doepfer_a100@y..., david.salter@r... wrote:
>
> Joe,
>
> Could you expand on "I like to keep my A160 available for switching
between the
> A155's rows"
>
> Regards
>
> David
>
>
>

> buechlerjoe

> <buechlerjoe@toa To:
Doepfer_a100@y...
> dmail.com> cc:

> Subject:
1 Re: Midi sync problem
> 22/12/2001 02:20 Header: Internal
Use Only
> Please respond

> to Doepfer_a100

>

>

>
>
>
> Hi bakis
>
> I assume you step down the A190's clock output with an A160 clock
> divider I like to keep my A160 available for switching between the
> A155's rows. Is there another way
>
> Joe
>
> --- In Doepfer_a100@y..., bakis Sirros <synth_freak_2000@y...>
wrote:
> > hi joe,
> > about your sync problem...i use the clock output of
> > the a190 to sync my a155.and the "problem" that i have
> > is that the a155 allways starts from the second
> > step.(of course i have the reset out of the a190
> > connected to the input of the a155...).i sync my a155
> > to my old atari st.but it's not a real problem as it
> > allways starts from the second step,everything else is
> > o.k..it might be that i have my a190 connected to midi
> > with my atari after a very long midichain.
> > why don't you use the clock out of the a190
> > bakis.
> >
> > --- buechlerjoe <buechlerjoe@t...> wrote:
> > > I tried out the Shepard generator when I first got
> > > the A191, but I'm
> > > sorry not to have any creative thoughts regarding it
> > > - I haven't
> > > switched the A191 to Shepard mode since then. The
> > > Midi/CV sockets and
> > > the Midi-synced LFOs are far too useful to me. I
> > > consider the A190/191
> > > to be a single integrated Midi interface, and I
> > > can't imagine trying
> > > to get by with just the A190 alone.
> > >
> > > A thought occurred to me about my sync problem. My
> > > previous master
> > > clock source might have been confusing the A191 in
> > > some mysterious
> > > way, sometimes leaving it in phase, sometimes out of
> > > phase. Perhaps it
> > > was in the "out of phase" state when I switched over
> > > to the Regelwerk.
> > > I'm going to temporarily re-connect the original
> > > clock source, and try
> > > to get the A191 back to the "in phase" state. If
> > > that doesn't work,
> > > I'll directly email Doepfer about the problem.
> > >
> > > Joe
> > >
> > > --- In Doepfer_a100@y..., bakis Sirros
> > > <synth_freak_2000@y...> wrote:
> > > > hi and wellcome to the list!
> > > > i wish i could help but,i don't have an a191...
> > > > by the way,as you have this module,tell us ,have
> > > you
> > > > used the shepard generator any creative
> > > thoughts
> > > > synthfreak
> > >
> > >
> >
> >
> >
> > =====
> > synthfreak(parallel worlds)
> > athens-greece
> > 1 group owner-moderator
> >
> > __________________________________________________
> > Do You Yahoo!
> > Send your FREE holiday greetings online!
> > http://greetings.yahoo.com
>
>
> Yahoo! Groups Sponsor
>
>
>
>
>
>
>
>
> To unsubscribe from this group, send an email to:
> doepfer_a100-unsubscribe@y...
>
>
>
> Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.
>
>
>
>
>
> -------------------------------------------------------------- --
> Visit our Internet site at http://www.reuters.com
>
> Any views expressed in this message are those of the individual
> sender, except where the sender specifically states them to be
> the views of Reuters Ltd.