Check what power they consume...amazing!!!


------------------------------------------------------
Danny Budts
info@...
www.syndromeda.be
https://www.facebook.com/Syndromeda
https://syndromeda.bandcamp.com/
https://www.facebook.com/pages/Syndromeda/189901007722025 ref=hl


----- Oorspronkelijk bericht -----
Van: 'Scott Rogers' scott@... 1 < Doepfer_a100@yahoogroups.com >
Aan: Doepfer a100 < Doepfer_a100@yahoogroups.com >
Verzonden: Fri, 30 Oct 2015 12:04:33 +0100 (CET)
Onderwerp: RE: 1 A-100PSU2

So is there going to be a problem using the Roland modules in my LC9 case

Thanks
Scott


-----Original Message-----
From: Doepfer_a100@yahoogroups.com [mailto: Doepfer_a100@yahoogroups.com ]
Sent: Friday, October 30, 2015 5:14 AM
To: Doepfer_a100@yahoogroups.com
Subject: AW: 1 A-100PSU2

Hello,

you find my answers written inline.

And there is an additional note in this regard: from about end of November a
new power supply will be available (A-100PSU3). It will offer 2000mA@+12V,
1200mA@-12V and has additional +5V with 4000mA available. It turned out that
there are many modules from other manufacturers available that take more
current than A-100 modules (e.g. the new Roland modules). Some of them also
require a high current at +5V. Internally the A-100PSU3 is a +/-15V
switching supply (wide range input 100...240V for mains voltage) followed by
the classical linear regulation circuit of the A-100PSU2 that generates
required +12V and -12V. Only the +5V is a pure switching supply without
linear regulation. We discovered that a pure 12V switching supply was not
good enough for the modular system (especially the load regulation was not
satisfying for all 12V switching supplies we tried). That's why we added the
well-tried linear regulation to the 15V switching supply.

Best wishes
Dieter Doepfer

> -----Ursprüngliche Nachricht-----
> Von: Doepfer_a100@yahoogroups.com
> [mailto: Doepfer_a100@yahoogroups.com ]
> Gesendet: Donnerstag, 29. Oktober 2015 16:36
> An: Doepfer_a100@yahoogroups.com
> Betreff: 1 A-100PSU2
>
>
> Hi everybody,
>
> short question: Are the 1200mA of the A-100PSU2 completely available or is

there any need for some kind of headroom

Each A-100PSU2 is tested with a dummy load of 10 Ohm which corresponds to
1200 mA. We also tested all kind of A-100 cases with built in A-100PSU2
under these conditions to find out if there may be thermal problems. All
results were OK. Consequently I can confirm that there is no need for a
headroom. As long as the sum of all currents of the A-100 modules driven by
the A-100PSU2 is less than
1200 mA everything is OK. The current for each A-100 module is specified on
the info page of each module. But one has to take the worst case, e.g. the
max. value (120 mA) for the headphone amplifer.
But I can speak only for A-100 modules and the statements are valid for
"normal" conditions. There is always some chance that a module takes more
current than specified because of a fault (e.g. defective integrated circuit
or electrolytic capacitor). But this is normally recognizable in the
malfunction of a module

> To be honest: My actual setup allows no headroom for headroom :-(
>
>
> Another quickie: Is there any difference between the voltage
> consumption of connected modules (buffered indeed) in use and unpatched

modules (but connected to the bus)

There is no difference if a module is patched or not. There is only one
module that comes to my mind where the current depends upon the usage: the
headphone amplifier (as already mentioned by Florian).

> Thank you so much for any clarifying reply.
>
>
> Best regards from Cologne/Germany
> Wolfram
>

------------------------------------

------------------------------------


------------------------------------

Yahoo Groups Links