"and for the Analogue systems modules made one out of a
strip of Vero board."
This is what I wanted to know. :)

For me, the 650mA (or something) coming out of the Asol PS will be
more than sufficient,I think. I'm planning a 9U system (19"). Which
should both fit the need as an external signal processor as well as
a "simple" Dual VCO mono synth. But it will take ages for me to fill
the full 9U, since I don't have a big budget.

But, what's a Vero board, where can I find one and how do I make a
strip from it

Thanks for all the info!!

Greetings, Zameer

--- In Doepfer_a100@y..., David Salter <david.salter@r...> wrote:
> Hi there Zameer,
>
> I know your question wasn't for me but I'll provide an answer
anyway as I have an equally large system of different euro modules.
>
> What is needed is a good quality LINEAR (not switch mode) power
supply providing +/- 12V with sufficient ampage to support your total
module set (and planned expansion).
>
> These can be purchased from many suppliers, mine was from an UK
based company
>
> http://www.amplicon.co.uk < http://www.amplicon.co.uk >
>
> Mine is (well there are two actually) 1.7A open frame Bentron S
series supplies, and I am very happy with them.
>
> All that is necessary is to connect the -12/+12 and ground to a bus
board ( I use the Doepfer ones and for the Analogue systems modules
made one out of a strip of Vero board.
>
>
>
> Hope that helps
>
>
>
> Regards
>
>
>
>
> David Salter
> Reuters Consulting
> Tel: +44 20 7542 2402
> Mob: +44 7990562402
> Fax: +44 20 7542 2699
>
> -----Original Message-----
> From: flamey101 1
> Sent: 11 September 2002 23:43
> To: Doepfer_a100@y...
> Subject: 1 Re: Slighty OT (again): Analogue
Systems ADSR mods
>
>
> I have one queation to you, Peter, since you have a bunch of
> different euro-modules in your systems..
> My current setup (a reeeaaal small one compared to yuors)
cosists of:
> An AS Filter, Osc, Doepfer amp, controls, etc.. isn't
important to my
> question actually.
> I have a Analogue Solutions Power supply board, on which I
can plug 2
> ASys modules into (the Osc and the filter). I do want to
expand my
> system with a frequency-to-voltage Asys thingie and add an
extra
> filter and Osc, maybe an extra Osc ass a waveshaper LFO. Or
could I
> get the same results with a slew limiter( ). So, what I was
> wondering, how did you supply the volts to your AS modules
> Did you built connectors/or cables yourself (hopefully)
>
> Greets, Zameer
>
> --- In Doepfer_a100@y..., "(i think you can figure that out)"
> <petergrenader@h...> wrote:
> > Sorry for this interesting, but slightly off-topic posting:
> >
> > for those of you interested in the mods I did on my
Analogue
> > Systems ADSR, go to:
> >
> > http://www.allegrobikes.com/franken.html
> >
> > and click on the the link 'modifications' in the first
paragraph of
> > descriptive text on the expansion panel.
>
>
>
> Yahoo! Groups Sponsor
> ADVERTISEMENT
>
< http://rd.yahoo.com/M=226671.2265556.3698777.2225242/D=egroupweb/S=17
05032144:HM/A=1201365/R=0/* http://shop.store.yahoo.com/cgi-bin/clink
sharperimage-
best+KFTN2Y:dmad/M=226671.2265556.3698777.2225242/D=egroupweb/S=170503
2144:HM/A=1201365/R=1/1031784173+si637.html>
> < http://us.adserver.yahoo.com/l
M=226671.2265556.3698777.2225242/D=egroupmail/S=:HM/A=1201365/rand=448
695315>
>
> To unsubscribe from this group, send an email to:
> doepfer_a100-unsubscribe@y...
>
>
>
> Your use of Yahoo! Groups is subject to the Yahoo! Terms of
Service < http://docs.yahoo.com/info/terms/ > .
>
>
>
>
> ------------------------------------------------------------- ---
> Visit our Internet site at http://www.reuters.com
>
> Any views expressed in this message are those of the individual
> sender, except where the sender specifically states them to be
> the views of Reuters Ltd.
>
>
> [Non-text portions of this message have been removed]