Dear group,

I have the following A-100 system for sale. I will NOT split up this
system, nor sell individual modules. The system is located in
Copenhagen, Denmark but I make frequent visits to Berlin, Germany and
I'm willing to deliver the system there - see terms near bottom.

Cases:
1x Doepfer G6 Case
1x Doepfer G3 Case
1x Third party 3U Eurorack case w/original Doepfer bus board connected
to PSU in G3 case.

Doepfer Modules:
2x A-110 VCO
1x A-114 Ring Modulator
1x A-115 Audio Divider
1x A-116 Waveform Processor
1x A-118 Noise + Random Voltages
1x A-119 External Input / Envelope Follower
1x A-120 24 dB Lowpass Filter (Transistor Ladder a la Moog)
1x A-121 12 dB Multi Mode Filter (Hi/Band/Low/Notch)
1x A-128 Fixed Filter Bank
1x A-130 Linear VCA
1x A-131 Exponential VCA
1x A-132-1 Dual Linear Low Cost VCA
2x A-138a Linear Mixer
1x A-138b Exponential Mixer
4x A-140 ADSR Envelope Generator
2x A-145 LFO 1
1x A-148 Sample & Hold
1x A-150 VC Switch
1x A-155 Analog/Trigger Sequencer
1x A-160 Clock Divider
1x A-161 Clock Sequencer
1x A-162 Dual Trigger Delay
1x A-170 Slew Limiter (Portamento)
1x A-175 Dual Voltage Inverter
1x A-176 Manual CV Source
1x A-180 Multiples 1 (Dual 4-way Multiples)
4x 8TE + 1x 2TE Blank Panels to complete 4 full rows + a few more
blank panels (4 and 8TE)

Homemade modules:
1x Triple 4-way Multiples (8TE)
1x Switched 5-way Multiples (1 unswitched and 4 switched sockets) (8TE)

1x Modified Tascam PB-32P Patch Bay (with 1/4" phone jack sockets),
configured as 4x 4-way multiples, 3 of which have a fifth connector to
the back (Good for patching up an external MIDI-CV converter, say Note
CV + Gate + Velocity CV) + 8 trunk lines. Takes up 1U. No mechanical
problems, but front plate is covered in stickers and has a couple of
minor scratch marks.

1x 2U rack shelf, 30cm deep, computer gray.

All of the above mounted in:

1x Wooden 19" studio rack case on wheels (2 locking, 2 non-locking),
19U inclined front, sturdy, well built, open rear, a few minor scratch
marks but otherwise fine.

Synthesizers.com:
1x QPS1 Power Supply Unit + DC cable harness
1x Q101 Power Control
1x Q102 AC Power Interface
1x Q104 MIDI Interface (Note CV, Gate, (Re)Trigger, Velocity CV)
1x Q125 Signal Processor (CV amplification/attenuation, inversion and offset)

Dotcom mounted in homemade wooden case (fairly sturdy, but not looking
good, open in back, fits quite neatly in remaining 6U space in rack if
you put it on the rack mounted shelf).

Patch cables, 3.5":
23x 30cm
13x 50cm
05x 80cm

Several 3.5" to 1/4" patch cables, assorted lengths, homemade.

All original Doepfer and Dotcom modules in good condition both
functionally and visually except for the following: They all have the
same marks around mounting holes as all other modules that have been
previously mounted and one knob on the A-155 is slightly bent and
scratched - it came that way from Thomann.de and after mailing back
and forth with them for a while I gave up trying to make them exchange
it as it works 100% according to spec and I stopped noticing the
difference. No other visual shortcomings that I've noticed, but won't
guarantee that you can't find a couple of minor scratches if you look
carefully.

Doepfer cases in good condition except for the following: Scratch
marks around holes for mounting in 19" rack. Bottom panel has been
removed from G3 case in order to enable connection to bus board in 3rd
party Eurorack frame. This cannot be seen when case is mounted in the
rack above the third party eurorack frame, and the original bottom
panel is included so the case can be restored to its original
configuration.

Photos available on demand.

Price as new of the original Doepfer parts (excl. cables) according to
doepfer.de website as of April 5th 2011 = 2810 Euros if you start with
a Basis System 1 (which is where this started).

Price as new of the original synthesizers.com parts according to
synthesizers.com website as of April 5th 2011 = 615 USD, slightly more
than 430 Euros according to Google.

Price as new of other parts unknown, but the studio rack alone should
cost at least a couple of hundred euros as new.

Asking 2150 Euros or 16.000,- Danish Kroner collected in Copenhagen,
Denmark or 2250 euros collected/delivered in Berlin, Germany. Cash on
collect. If you prefer to collect/have it delivered in Berlin I
require 200 Euros in advance payment / as deposit. This is in case you
don't show up/answer the door. It will also take a couple of weeks to
arrange transport.

System can be sent to other destinations. Buyer pays all shipping
costs, payment in advance.

Please inquire off-list unless there's a good reason to do otherwise.

Happy patching,
Silas