Hi York. I think I had plugged the A190-2 the wrong way and might damaged the unit. It seemed to be working fine, receiving midi messages and activating the A110 both from the CV1 and pitch bend from CV2. But the gate output problem indicated there is something wrong really.

Thank you for the kind attention.

Sidney

--- In Doepfer_a100@yahoogroups.com , "York Luethje" <ybl@...> wrote:
>
> Hi Sidney,
>
>
>
> Unfortunately I am not directly familiar with the A-190-2. In the manual
> there is a diagram of the circuit board where a trim pot for the CV scale is
> indicated. Trimming this might solve your tuning issue. As for the missing
> gate I am at a loss tbh. It's quite possible that your unit is faulty. Did
> you buy it from a dealer I would contact the seller or Doepfer directly:
> software(at)doepfer.de
>
>
>
> Hope you get your module fixed.
>
>
>
> York
>
>
>
> _____
>
> Von: Doepfer_a100@yahoogroups.com [mailto: Doepfer_a100@yahoogroups.com ] Im
> Auftrag von Sidney
> Gesendet: Freitag, 4. Februar 2011 16:33
> An: Doepfer_a100@yahoogroups.com
> Betreff: 1 Re: Can't trigger A-140 from A-190-2
>
>
>
>
>
> Hello York. I am connecting my midi keyboard with a standard midi cable to
> the midi input from A190-2 interface.
>
> I also notice that the VCO doesn't make a tonal scale sound as I press notes
> from the keyboard. For example, if I press a C3 then a C4 on the keyboard I
> hear another interval instead of an octave. I kept the system turned on for
> more than 20 minutes as I read it needs some time to make it get in tune.
>
> Sidney
>
> --- In Doepfer_a100@yahoogroups.com <mailto:Doepfer_a100%40yahoogroups.com>
> , "York Luethje" <ybl@> wrote:
> >
> > Hi Sydney, how are you adressing the Midi interface
> >
> >
> >
> > _____
> >
> > Von: Doepfer_a100@yahoogroups.com <mailto:Doepfer_a100%40yahoogroups.com>
> [mailto: Doepfer_a100@yahoogroups.com <mailto:Doepfer_a100%40yahoogroups.com>
> ] Im
> > Auftrag von Sidney
> > Gesendet: Freitag, 4. Februar 2011 12:36
> > An: doepfer_a100@yahoogroups.com <mailto:doepfer_a100%40yahoogroups.com>
> > Betreff: 1 Can't trigger A-140 from A-190-2
> >
> >
> >
> >
> >
> > Hello everybody. I'm a totally newbie and just assembled my
> > A-100 mini system this week. It has a A-190-2, A-110, A-106-1, A-145,
> > A-132-3 and A-140 assembled on a Tiptop Happy ending kit.
> >
> > I tried to send a gate output from the A-190-2 midi interface to the A-140
> > ADSR gate input but nothing happened. I connected the A-145 LFO to the
> A-140
> > and then it's 'ADSR Contr.' light turned on. The 'ADSR Contr.' light also
> > turned on when it received signal from the waveforms output from the VCO.
> Is
> > there another way to trigger the A-140 Maybe the 190-2 gate output is
> > faulty
> >
> > I followed the "Simple synthesizer standard patch with one envelope
> > generator" diagram from page 11 of A-190-2 (since it is a very similar
> > system as mine except for the different filter module) but could not get a
> > sound from it.
> >
> > I just removed the two jumpers from A-190-2 and the junper from A-140 but
> > nothing changed.
> >
> > Thank you,
> >
> > Sidney H.
> >
> >
> >
> >
> >
> > [Non-text portions of this message have been removed]
> >
>
>
>
>
>
> [Non-text portions of this message have been removed]
>