hello Florian,
i think so too.
so, what do i do
Bakis.



--- Florian Anwander < Florian.Anwander@... >
wrote:

> Hi Bakis
>
> I think it is simply a DC-coupled precision-CV-mixer
> for two inputs:
> first input is fixed and is fed through 1:1. The
> second input which can
> add a voltage in a range between -10 and + 10 Volts.
> Maybe this should
> be solved as a DIY-project (it is very simple).
>
> Florian
>
> Bakis Sirros wrote:
>
> > hello Dieter and all,
> > yes, but i do not understand the purpose of this
> > module.
> > would it be a dual vca/offset module
> > but a vca module with offset is the 130 vca,
> right
> > what would be the benefit of making a dual a130
> > module only the inclusion of "a119 type" ext
> input
> > amplification build in
> > best regards,
> > Bakis.
> >
> >
> >
> > --- hardware@... wrote:
> >
> >
> >>As I'm doubtful how many users are asking for such
> a
> >>dual module (keeping in
> >>mind that we already have A-176 and the offset
> >>functions of the mixers and
> >>the 5-fold offset/attenuator module A-129-3). I
> ask
> >>you (Bakis) to start a
> >>poll for such a 2-fold offset module. Thank you.
> >>
> >>Dieter Doepfer
> >>
> >>
> >>>-----Ursprungliche Nachricht-----
> >>>Von: Doepfer_a100@yahoogroups.com
> >>>[mailto: Doepfer_a100@yahoogroups.com ]Im Auftrag
> >>
> >>von Silas Johansen
> >>
> >>>Gesendet: Montag, 18. Juni 2007 18:42
> >>>An: Doepfer_a100@yahoogroups.com
> >>>Betreff: Re: 1 Re: adding cv offset
> >>>
> >>>
> >>>A voltage offset module would be convenient in
> the
> >>
> >>patches below:
> >>
> >>>Audio source --> A-119 --> Voltage Offset -->
> >>
> >>A-155 lower row ext. input
> >>
> >>>LFO/VCO --> Voltage Offset --> A-155 lower row
> >>
> >>ext. input
> >>
> >>>An input voltage attenuator would be convenient.
> >>
> >>Built in amplification of
> >>
> >>>line level signals would eliminate the need for
> an
> >>
> >>A-199 in the
> >>
> >>>first patch.
> >>>
> >>>One could fit two of these to an 8HP panel if
> each
> >>
> >>included only in & out
> >>
> >>>jacks and input attenuator/amplifier and voltage
> >>
> >>offset knobs. One half
> >>
> >>>would even have room for an extra jack, perhaps
> >>
> >>inverse out or an extra CV
> >>
> >>>input with or without attenuator (without
> >>
> >>attenuator would be useful for
> >>
> >>>voltages coming from a 1V/Oct. CV source) and an
> >>
> >>extra pot, the
> >>
> >>>aforementioned attenuator for input two or fine
> >>
> >>tune of voltage offset.
> >>
> >>>Undoubtedly somebody will have other good
> >>
> >>suggestions.
> >>
> >>>Without an input each half should output the
> >>
> >>offset voltage. This would in
> >>
> >>>my opinion make for a module similar to but much
> >>
> >>more useful than
> >>
> >>>the A-176,
> >>>especially if one half had fine control of offset
> >>
> >>and an
> >>
> >>>unattenuated input.
> >>>Granted, only two outputs would be available, but
> >>
> >>the addition of
> >>
> >>>the offset
> >>>feature would make up for it.
> >>>
> >>>Also, the tuning range of my VCOs is limited to a
> >>
> >>couple of half
> >>
> >>>tone steps.
> >>>Detuning one by a larger amount requires the use
> >>
> >>of a constant CV
> >>
> >>>source and
> >>>either a mixer or the CV2 input - this module,
> >>
> >>esp. with an unattenuated
> >>
> >>>input, would be a killer for "fat fifth" type
> >>
> >>sounds.
> >>
> >>>What I'm describing above is similar and in my
> >>
> >>opinion superior to the
> >>
> >>>dotcom q125.
> >>>
> >>>/Silas
> >>>
> >>>On 6/18/07, hardware@...
> >>
> >>< hardware@... > wrote:
> >>
> >>>> > ... but i'm surprised that there is no
> >>
> >>dedicated offset module -
> >>
> >>>>>something like 4HE with an input, output and a
> >>
> >>+/- knob that
> >>
> >>>>>could regulate a constant output when nothing
> >>
> >>is connected to
> >>
> >>>the input.
> >>>
> >>>>With a few exceptions (e.g. A-132) both an
> >>
> >>offset control and a control
> >>
> >>>>voltage input with attenuator are available for
> >>
> >>each voltage controlled
> >>
> >>>>parameter of a module. This is why normally
> >>
> >>separate offset
> >>
> >>>generators and
> >>>
> >>>>attenuators are not necessary in the A-100.
> >>>>
> >>>>If necessary (e.g. as an offset for the A-132)
> >>
> >>the manual CV
> >>
> >>>source A-176
> >>>
> >>>>could be used as an offset generator. This is
> >>
> >>why I don't see the
> >>
> >>>>necessity
>

=== message truncated ===


Bakis Sirros - Parallel Worlds / Interconnected / Memory Geist
1 group owner
http://www.parallel-worlds-music.com
http://www.myspace.com/parallelworldsmusic
http://www.myspace.com/interconnectedmusic
http://www.myspace.com/memorygeist
http://www.DiN.org.uk
http://www.shimarecords.co.uk
http://www.rubber.gr
Athens-Greece



____________________________________________________________________________________Ready for the edge of your seat
Check out tonight's top picks on Yahoo! TV.
http://tv.yahoo.com/