so, Silas:
if you are sure what this module should do and what
features should have, then, please, tell me "exactly"
what the poll should say.
then i can create it.
best regards,
Bakis.


--- Silas Johansen < sijodk@... > wrote:

> Hadn't considered getting the A-129-3 for this
> purpose. It suits my needs
> quite satisfactorily (except I'm not sure if I get
> exactly 1.00 x
> amplification is I turn the attenuator knob all the
> way to the right) so I'm
> tempted to get one. Also, I'm very well aware that
> between the members of
> this list we can probably come up with a thousand
> designs for modules that
> would work perfectly for some particular purpose,
> but most of them would
> probably only be sold in *very* limited quantities
> (like one or two to
> whoever came up with the idea).
>
> Also, my ideas for this module should prove fairly
> simple to implement, so
> it's probably a good DIY project. I will therefore
> be tempted to vote no to
> my own suggestion when the poll comes up.
>
> /Silas
>
> On 6/19/07, hardware@...
> < hardware@... > wrote:
> >
> > As I'm doubtful how many users are asking for
> such a dual module
> > (keeping in
> > mind that we already have A-176 and the offset
> functions of the mixers and
> > the 5-fold offset/attenuator module A-129-3). I
> ask you (Bakis) to start a
> > poll for such a 2-fold offset module. Thank you.
> >
> > Dieter Doepfer
> >
> > > -----Ursprungliche Nachricht-----
> > > Von: Doepfer_a100@yahoogroups.com
> <Doepfer_a100%40yahoogroups.com>
> > > [mailto: Doepfer_a100@yahoogroups.com
> <Doepfer_a100%40yahoogroups.com>]Im
> > Auftrag von Silas Johansen
> > > Gesendet: Montag, 18. Juni 2007 18:42
> > > An: Doepfer_a100@yahoogroups.com
> <Doepfer_a100%40yahoogroups.com>
> > > Betreff: Re: 1 Re: adding cv offset
> >
> > >
> > >
> > > A voltage offset module would be convenient in
> the patches below:
> > >
> > > Audio source --> A-119 --> Voltage Offset -->
> A-155 lower row ext. input
> > > LFO/VCO --> Voltage Offset --> A-155 lower row
> ext. input
> > >
> > > An input voltage attenuator would be convenient.
> Built in amplification
> > of
> > > line level signals would eliminate the need for
> an A-199 in the
> > > first patch.
> > >
> > > One could fit two of these to an 8HP panel if
> each included only in &
> > out
> > > jacks and input attenuator/amplifier and voltage
> offset knobs. One half
> > > would even have room for an extra jack, perhaps
> inverse out or an extra
> > CV
> > > input with or without attenuator (without
> attenuator would be useful for
> > > voltages coming from a 1V/Oct. CV source) and an
> extra pot, the
> > > aforementioned attenuator for input two or fine
> tune of voltage offset.
> > > Undoubtedly somebody will have other good
> suggestions.
> > >
> > > Without an input each half should output the
> offset voltage. This would
> > in
> > > my opinion make for a module similar to but much
> more useful than
> > > the A-176,
> > > especially if one half had fine control of
> offset and an
> > > unattenuated input.
> > > Granted, only two outputs would be available,
> but the addition of
> > > the offset
> > > feature would make up for it.
> > >
> > > Also, the tuning range of my VCOs is limited to
> a couple of half
> > > tone steps.
> > > Detuning one by a larger amount requires the use
> of a constant CV
> > > source and
> > > either a mixer or the CV2 input - this module,
> esp. with an unattenuated
> > > input, would be a killer for "fat fifth" type
> sounds.
> > >
> > > What I'm describing above is similar and in my
> opinion superior to the
> > > dotcom q125.
> > >
> > > /Silas
> > >
> > > On 6/18/07, hardware@...
> <hardware%40doepfer.de> <
> > hardware@... <hardware%40doepfer.de>>
> wrote:
> > > >
> > > > > ... but i'm surprised that there is no
> dedicated offset module -
> > > > > something like 4HE with an input, output and
> a +/- knob that
> > > > > could regulate a constant output when
> nothing is connected to
> > > the input.
> > > >
> > > > With a few exceptions (e.g. A-132) both an
> offset control and a
> > control
> > > > voltage input with attenuator are available
> for each voltage
> > controlled
> > > > parameter of a module. This is why normally
> separate offset
> > > generators and
> > > > attenuators are not necessary in the A-100.
> > > >
> > > > If necessary (e.g. as an offset for the A-132)
> the manual CV
> > > source A-176
> > > > could be used as an offset generator. This is
> why I don't see the
> > > > necessity
> > > > of a dedicated offset module. But I'm open for
> suggestions if I
> > > overlooked
> > > > something.
> > > >
> > > > Best wishes
> > > > Dieter Doepfer
> > > >
> > > >
> > > >
> > >
> > >
> > > [Non-text portions of this message have been
> removed]
> > >
> > >
> > >
> > >
> > > Yahoo! Groups Links
> > >
> > >
> > >
> >
> >
> >
>
>
> [Non-text portions of this message have been
> removed]
>
>

Bakis Sirros - Parallel Worlds / Interconnected / Memory Geist
1 group owner
http://www.parallel-worlds-music.com
http://www.myspace.com/parallelworldsmusic
http://www.myspace.com/interconnectedmusic
http://www.myspace.com/memorygeist
http://www.DiN.org.uk
http://www.shimarecords.co.uk
http://www.rubber.gr
Athens-Greece



____________________________________________________________________________________
Be a better Globetrotter. Get better travel answers from someone who knows. Yahoo! Answers - Check it out.
http://answers.yahoo.com/dir/ link=list&sid=396545469